ماكينة تخريم الورق Ferag FERAG line




















إذا قررت شراء المعدات بسعر منخفض، فتأكد أنك تتواصل مع البائع الحقيقي. اكتشف أكبر قدر ممكن من المعلومات عن مالك المعدات. تتمثل إحدى طرق الغش في تقديم نفسك كشركة حقيقية. إن ساورك شك، أخبرنا عن ذلك من أجل تشديد الرقابة وذلك من خلال نموذج التعليقات.
قبل أن تقرر القيام بالشراء، احرص على مراجعة العديد من عروض البيع بعناية لفهم متوسط تكلفة المعدات التي اخترتها. إذا كان سعر العرض الذي أعجبك أقل بكثير من عروض مشابهة، ففكر في الأمر بتأنٍ. قد يكون هناك فرق أسعار هائل يشير إلى عيوب مخفية أو أن البائع يحاول ارتكاب أعمال احتيالية.
ابتعد عن شراء المنتجات التي يكون سعرها مختلف بشدة عن متوسط السعر لمعدات مشابهة.
لا توافق على الوعود المثيرة للشكوك والبضائع المدفوعة مسبقًا. إن ساورك شك، فلا تخاف من طلب توضيح التفاصيل وأن تطلب صورًا ومستندات إضافية للمعدات وأن تفحص صحة التصديق على تلك المستندات وتطرح الأسئلة التي تساورك.
أكثر أنواع الاحتيال شيوعًا، قد يطلب البائعون غير المنصفون مبلغًا معينًا كعربون مسبق "لتحجز" حقك في شراء المعدات. وبالتالي يستطيع المحتالون تجميع مبلغًا ضخمًا ثم يختفون ولا تستطيع التواصل معهم بعد ذلك.
- إرسال الدفعة المسبقة إلى البطاقة
- لا تقم بالدفع المسبق بدون مستندات ورقية تؤكد عملية تحويل الأمول إذا ساورك أي شك في البائع خلال التواصل.
- إرسال إلى حساب "الوصي" “Trustee”
- هذا الطلب ينبغي أن يكون بمثابه إنذار فأنت على الأرجح تتواصل مع شخص محتال.
- إرسال إلى حساب الشركة باسم مشابه
- توخّ الحذر، فقد يختفي المحتالون أنفسهم أيضًا خلف شركات معلومة أو يدخلون تغييرات طفيفة على الاسم. لا تحول الأموال إذا ساورك شك في اسم الشركة.
- استبدال البيانات الخاصة في فاتورة شركة حقيقية
- قبل التحويل، تأكد أن البيانات المحددة صحيحة وأنها ترتبط أو لا ترتبط بالشركة المحددة.
معلومات الاتصال بالبائع



















FERAG wire stitching machine
Binding block format V1
Gross: min 152 × 217 – max315 × 340
Net: min 148 × 210 – max 300 × 332
Insert for feeder station
Min 110 × 95 – max 315 × 340
Gluing of sheets only – no blocks
Net format
min 55 × 85 – max 280 × 200
min 85 × 55
Advertising sleeves and folded inserts with one fold must be tested
Number of insert feeders 8
Number of glued-sheet feeders 1
Maximum block thickness 5 mm
Insert pre-fold
8 to 12 mm – back pre-fold only
Insert without pre-fold
Possible
but not across the entire format range
Double production
Cutting in the machine not allowed
Trimming
Head and foot trimming 3.5 – 50 mm
Side trimming 3.5 – 50 mm
Landscape format cannot be trimmed on the three-knife trimmer
which differs structurally from saddle stitchers and wire stitchers
Staples
Number of standard stitching staples
2 or 3
Staple size 15 mm
Distance between the two outermost staples 160 mm (measured from staple centers)
Distance from outer staple to center
80 mm (measured from staple centers)
Staples are fixed in position and individual ones can be deactivated
however
the product can be shifted relative to the staples
With two staples
For A4 format: the top and bottom staples are used
the middle one is deactivated
For A5 format: the top and middle staples are used
the bottom one is deactivated
Hanging eyes Not possible
Cover
The cover must be folded before saddle stitching. It is fed from the insert feeder. Optionally use Unicover
Paper weight for A4 cover
80 – 300 g/m² for wood-free and coated papers
max. 255 g/m² for folding boxboard
A4 cover weight min. 10 g
A cover with an outward flap is not possible – it can only be processed with the flap inward
then manually turned upward afterwards
Half-cover
Loaded from the insert feeder and must be folded before saddle stitching
Paper weight 130 – 200 g/m²
Minimum half-cover width for A4 format 110 mm
Inserts
Minimum insert weight: 10 g
24-page A4 insert (Lithoman 3) has priority over a 16-page + 8-page combination
12-page A4 insert (Lithoman 3) has priority over an 8-page + 4-page combination
Inserts of approximately equal weight have priority over inserts with very different weights
All 16-page inserts have priority over all 8-page inserts
Find more here
إظهار قائمة الأسماء
Contact us at
إظهار قائمة الأسماء